Wireless Power Minimizes Interconnection Problems

« Bossun Switches    Bossun Switches    2096    7/26/2010»


News & Features From Auto Electronics
Committed to improving hybrid electric cars
New Motors for Hybrid Vehicles
Battery Firms Battle for Hybrid Hegemony
Innovative Bipolar Plates for Fuel Cells

  See More Headlines
Top Articles
Exploring Current Transformer Applications
Ultracapacitor Technology Powers Electronic Circuits
Buck-Converter Design Demystified
Sensorless Motor Control Simplifies Washer Drives

PET Resources
Buyer's Guide
Engineering Jobs
Power Electronics Events
Rent Our Lists
Spotlight on Digital PowerFind a downloadable version of this story in pdf format at the end of the story.

Use of wireless power involves the magnetic coupling of conductors configured so that the change in current flow through one conductor transfers a voltage in another conductor through electromagnetic induction . The amount of inductive coupling between two conductors is determined by their mutual inductance.

You can enhance wireless power transmission with the application of resonance effects. This technique employs transmitter and receiver inductors tuned to a mutual frequency. This enables power to be transmitted over a distance of up 1/4 or 1/3 times the size of the primary coil. Transmitting and receiving coils are usually single layer solenoids or flat spirals with series capacitors, which, in combination, allow the receiving element to be tuned to the transmitter frequency.

Electromagnetic induction is a function of the frequency and the intensity of the conductors current and voltage that produces the fields. The higher the frequency, the greater the induction effect. Energy transfers from the conductor that produces the fields (the primary) to any conductor on which the fields impinge (the secondary). You can increase the coupling between two conductors by winding them into coils and placing them close together on a common axis, so the magnetic field of one coil passes through the other coil. Coupling must be tight to achieve high efficiency. If the distance from the primary to the secondary increases some of the magnetic field will miss the secondary, lowering the coupling.

Common uses of resonance-enhanced electrodynamic induction are charging the batteries of laptop computers and cell phones, medical implants and electric vehicles. A localized charging technique selects the appropriate transmitting coil in a multilayer winding array structure. Fig. 1 shows a typical wireless transmitter. Resonance is used in both the wireless charging pad (the transmitter circuit) and the receiver module (embedded in the load) to maximize energy transfer efficiency. This approach has been adopted as part of the Qi (pronounced chee) wireless charging standard developed by the Wireless Power Consortium.

The effectiveness of the electrodynamic induction is called link efficiency, link. It is a measure of the primary and secondary coils ability, to transfer energy from one coil to the other:



k = Magnetic coupling factor


= Unloaded quality factor of the primary circuit


= Unloaded quality factor of the secondary circuit


= QE = Effective Q


RE = Effective load resistance which models the rectifier including the output filter capacitor and the actual load resistance RL. The relationship between RE and RL is


If series resonance is used on the secondary side

= Primary angular velocity (2f)
2 =Secondary angular velocity (2f2)
L 1 = Primary inductance in Henries
r 1 = Primary dc resistance in Ohms
L 2 = Secondary inductance in Henries
r 2 =Secondary dc resistance in Ohms

The loaded quality factor is:


For maximum efficiency:
Tune the link to the secondary resonant frequency
Set the effective load resistance to:


To maximize kQ (figure of merit):


Q is called the system quality factor. It should be noted that a low magnetic coupling can be compensated by an increased system quality factor.

Therefore, optimum efficiency =


Fig. 2 plots the optimum link efficiency as a function of the figure of merit for the coils, which is opt vs. kQ.

One way to manage a high k value is to use a ferromagnetic shield (core) enhances the magnetic coupling factor and reduces the stray magnetic field. Fig. 3 shows the magnetic field resulting from a ferromagnetic shield with and without ferromagnetic shielding.

Another way to manage a high efficiency inductive solution is maximize the Q or Quality factor for the inductive coils. Table 1 lists typical wireless power core from RRC and Fig. 4 are plots of Q vs. Frequency for these cores.

Generally, for any type of coil type the magnetic coupling factor, k, can be improved by reducing the vertical distance between the coils and aligning the coils vertically as shown in Fig. 5a, lateral misalignment (Fig. 5b) and angular misalignment (Fig. 5c) degrade efficiency.



  • Previous :Tactile switches - Switches technology

  • Next : The last